You are viewing pudeev

entries friends calendar profile My LJ Previous Previous Next Next
Michael V. Pudeev - GPL Source Code for DSL-2640
pudeev
pudeev
Share
GPL Source Code for DSL-2640
D-Link DSL-2640U Hardware version: B2
GPL Source Code for firmware version RU_V3.06
http://ftp.dlink.ru/pub/ADSL/GPL_source_code/RU_DSL-2640U/RU_DSL-2640U_3-06-04-3C_GPL.tar.gz

D-Link DSL-2640U Hardware version: D1
GPL Source Code for firmware version RU_1.10
http://tsd.dlink.com.tw/temp/download/3074/DLink_DSL-2640U_RU_1.10_GPL.tar.gz

D-Link DSL-2640B Hardware version: B2
GPL Source Code for firmware V4.00
ftp://ftp.dlink.fr/DSL/DSL-2640B/GPL/EU_DSL-2640B_EU_4.00_3-10-02-29_GPL.tar.gz
GPL Source Code for firmware V3.07
http://tsd.dlink.com.tw/temp/download/3069/EU_DSL-2640B_EU_3.07_3-06-06-4A_GPL.tar.gz
GPL Source Code for firmware V3.06
http://tsd.dlink.com.tw/temp/download/2891/EU_DSL-2640B_3-06-06-46_GPL.tar.gz

D-Link DSL-2640B Hardware version: B3
GPL Source Code for firmware V5.00
ftp://ftp.dlink.pl/dsl/dsl-2640b/driver_software/DSL-2640B_gpl_revB3_5-0-0_eu_en_20100420.tar.gz


ну, и до кучи, ссылка на эмулятор интерфейса устройств D-Link:
http://www.support.dlink.com/emulators/dsl2640b/306041/vpivci.html

Tags: , , , , , , , , , ,

Comments
lisnenko From: lisnenko Date: September 17th, 2008 03:38 pm (UTC) (Link)
Михаил, а в чем разница между этими аппаратными ревизиями?

Как определить какая стоит у меня?

Какая лучше, в чем конкретно?
pudeev From: pudeev Date: September 20th, 2008 05:30 pm (UTC) (Link)
1. Незнаю.
По исходникам видно что CPU тот же самый, а Board ID = A96348GW. У меня H/W version: "B2", Board ID = D-4P-W.

Вот инфа из GPL RU_1.10 для D-Link DSL-2640U Hardware version: D1

MODEL=DSL-2640U
VERSION=RU_1.10
BCM_VERSION=3.10L.01.
Revision=4553
FSSTAMP=20080805203248
BRCM_VERSION=3
BRCM_RELEASE=10
BRCM_EXTRAVERSION=01
BRCM_BOARD_ID="A96348GW"
BRCM_CHIP=6348

2. По шильдику на днище корпуса модема или смотри стикер на коробке, печатной плате:
http://pudeev.livejournal.com/26318.html

3. Первый абзац пункта 1.


А у тебя какая H/W version?
lisnenko From: lisnenko Date: September 21st, 2008 08:32 am (UTC) (Link)
B2
From: (Anonymous) Date: September 22nd, 2008 04:45 pm (UTC) (Link)

ЛАВРИК

ммиша а ты дорабатывал скрипт сборки прежде чем компилировал прошивку?.
а то у меня ошибку выдает и не компилирует, использую fedore core 9.
естевственно из под root.
что то там пишет про static декларации.
pudeev From: pudeev Date: September 23rd, 2008 05:20 pm (UTC) (Link)

Fedora Core 9 и RU_DSL-2640U_3-06-04-3C_GPL

Да, на FC 9 при запуске скрипта выходит ошибка:
scripts/kconfig/mconf.c:91: error: static declaration of 'current_menu' follows non-static declaration
scripts/kconfig/lkc.h:63: error: previous declaration of 'current_menu' was here


Как вариант, использовать компилятор GCC 3.xx вместо 4.xx

1. OS Fedora Core 9 и компилятор GCC 4.3
[root@localhost /]# uname -ro
2.6.26.3-29.fc9.i686 GNU/Linux
[root@localhost /]# gcc -dump version
4.3.0

2. Скачиваем и устанавливаем пакеты для gcc32 из дистрибутива Fedora Core 5:
compat-libstdc33: Compatibility standard C libraries
compat-gcc-32: The compatibility GNU Compiler Collection
compat-gcc-32-c++: C++ support for compatibility compiler

[root@localhost Download]# wget http://ftp.unixcenter.ru/Fedora/linux/core/5/i386/os/Fedora/RPMS/compat-libstdc++-33-3.2.3-55.fc5.i386.rpm

[root@localhost Download]# wget http://ftp.unixcenter.ru/Fedora/linux/core/5/i386/os/Fedora/RPMS/compat-gcc-32-3.2.3-55.fc5.i386.rpm

[root@localhost Download]# wget http://ftp.unixcenter.ru/Fedora/linux/core/5/i386/os/Fedora/RPMS/compat-gcc-32-c++-3.2.3-55.fc5.i386.rpm

[root@localhost Download]# rpm -Uph compat-gcc-32-3.2.3-55.fc5.i386.rpm compat-libstdc++-33-3.2.3-55.fc5.i386.rpm compat-gcc-32-c++-3.2.3-55.fc5.i386.rpm
########################################### [100%]
        package compat-libstdc++-33-3.2.3-55.fc5.i386 is already installed
        package compat-gcc-32-3.2.3-55.fc5.i386 is already installed
        package compat-gcc-32-c++-3.2.3-55.fc5.i386 is already installed

[root@localhost Download]# gcc32 -dumpversion
3.2.3

3. Переименуем gcc и создаем символьную ссылку на gcc32:
[root@localhost /]# cd /usr/bin
[root@localhost bin]# mv gcc gcc43
[root@localhost GPL_2640U_B]# ln -sf gcc32 gcc


Удачи!
From: (Anonymous) Date: December 10th, 2008 04:57 am (UTC) (Link)

Re: Fedora Core 9 и RU_DSL-2640U_3-06-04-3C_GPL

scripts/kconfig/mconf.c:91: error: static declaration of 'current_menu' follows non-static declaration

Я просто закомментировал эту строку в kernel/linux/scripts/kconfig/mconf.c - поехало собираться. По идее, оно всё равно gcc для mips собирает.

Застряло на нехватке libstdc++.so.5
From: (Anonymous) Date: December 10th, 2008 05:07 am (UTC) (Link)

Re: Fedora Core 9 и RU_DSL-2640U_3-06-04-3C_GPL

yum search compat|grep stdc
и далее поставить чего-там-оно написало:
yum install compat-libstdc++-33
т.е. смысла тащить старый gcc нету.

А у меня проблема - ppp сессия обрывается (провайдером) и не рестартится - ни автоматом, ни через веб-морду. Только ребут или питание подёргать.
Не знаю, правда, это на всех прошивках так, или только на "последней" с dlink.ru (2640U/hw. rev B2)
From: outfitkarst Date: October 1st, 2008 08:29 pm (UTC) (Link)
Очень понравился ваш ЖЖ, я вас зафренжу и было бы круто если бы вы ответили взаимно;)
From: (Anonymous) Date: October 24th, 2008 07:01 pm (UTC) (Link)

Хорошие новости... OpenWrt на модемах с чипом Broadcom BCM63xx ... жд

New Broadcom BCM63xx codebase with GPL'd Ethernet and USB support

Changeset https://dev.openwrt.org/changeset/13001 introduces a new Broadcom BCM63xx SoC codebase which supports the following parts :

- new core support (arch/mips/bcm63xx)
- integrated ethernet MAC
- integrated ethernet PHY
- OHCI and EHCI USB host controllers
- BCM6348 and BCM6358 board support

This work was done by Maxime Bizon from Freebox SA for whom I would like to give huge thanks for his high quality and valuable work
as well as this great contribution.

Prior to this codebase, we were sticking with some old and hardly maintainable BCM63xx codebase.
I encourage the OpenWrt community to test this codebase and report any problems you meet using Trac at https://dev.openwrt.org.

Future work will focus on :

- adding support for BCM6338, BCM6345, BCM6368 and BCM6816 using the existing infrastructure
- merging watchdog and master SPI drivers


Broadcom 63xx SOCs support in linux-mips and OpenWrt
Last sunday, Maxime Bizon has submitted a series of patches to the linux-mips mailing list, adding support for Broadcom 63xx SOCs. Shortly after, these patches have been added to OpenWrt by Florian Fainelli.

This is definitely great news, because the old BCM63xx codebase was old and hardly maintainable, whereas the new one includes GPL'd Ethernet and USB support.

What is even better is that Freebox SA (Maxime's employer) and Broadcom have agreed to let Maxime publish his patches (under GPL).

Here is what these 12 patches support:
- new core support (arch/mips/bcm63xx)
- integrated ethernet MAC
- integrated ethernet PHY
- OHCI and EHCI USB host controllers
- BCM6348 and BCM6358 board support

Routers based on 6348 or 6358 SOCs include:
- 3Com 3CRWDR200A-75
- Asus AM200g / AM604 / AM604G / WL600G
- Belkin F5D7633-4B / F5D9630-1/2/3/5
- Comtrend CT536/1+ / CT638/1
- D-Link DSL2640B / DSL2740B / DSL2741B
- Davolink DV201AMR
- Dynalink RTA1046VW
- Hitachi AH4021 / AH4222
- Huawei HG520 / HG550
- Linksys WAG54GS / WAG54GX2 / WAG300N / WAG325N
- Netgear DG834G / DG834GT / DG834N / DG834PN
- T-Com Speedport 500V / W500V
- Thomson ST585 / ST780
- USRobotics USR9107 / USR9108 / USR9113 / USR9114
- Zhone 6218 / 6228 / 6238

There are also numerous european ISP using DSL router / gateways based on these Broadcom SOCs:
- BT Voyager 2091/2100/2110 (BT [UK ISP], hacking)
- Neufbox 4 (SFR [FR ISP], hacking)
- Freebox v4 (Free [FR ISP], hacking)
- Livebox (Orange [FR ISP], hacking)
- Speedport (Deutsche Telekom [DE ISP], hacking)
- W-Gate (Alice [IT ISP], hacking)

Future work will focus on:
- adding support for BCM6338, BCM6345, BCM6368 and BCM6816 using the existing infrastructure
- merging watchdog and master SPI drivers

Now's time to free your router. Happy hacking!

http://www.dd-wrt.com/phpBB2/viewtopic.php?t=39698

From: (Anonymous) Date: March 2nd, 2010 02:44 pm (UTC) (Link)

OpenWrt на USR9107A (Broadcom BCM6348)

http://downloads.openwrt.org/snapshots/trunk/brcm63xx/

CFE> flashimage 192.168.1.100:openwrt-96348R-A-squashfs-bc300-cfe.bin
Loading 192.168.1.100:openwrt-96348R-A-squashfs-bc300-cfe.bin ...
Finished loading 1835012 bytes
..................................

Finished flashing image.
Resetting board...

CFE version 1.0.37-1.5 for BCM96348 (32bit,SP,BE)
Build Date: Fri Jul  1 08:33:19 CDT 2005 (root@localhost.localdomain)
Copyright (C) 2000-2005 Broadcom Corporation.

Boot Address 0xbfc00000

Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV160T, id 0x22c4, size 2048KB
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 8388608 bytes (8MB)

Total memory used by CFE:  0x80401000 - 0x80524F80 (1195904)
Initialized Data:          0x8041C3B0 - 0x8041E710 (9056)
BSS Area:                  0x8041E710 - 0x80422F80 (18544)
Local Heap:                0x80422F80 - 0x80522F80 (1048576)
Stack Area:                0x80522F80 - 0x80524F80 (8192)
Text (code) segment:       0x80401000 - 0x8041C3AC (111532)
Boot area (physical):      0x00525000 - 0x00565000
Relocation Factor:         I:00000000 - D:00000000

Board IP address                  : 192.168.1.1
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id Name                     : 96348R-A
Psi size in KB                    : 24
Number of MAC Addresses (1-32)    : 11
Base MAC Address                  : 00:14:c1:11:3c:2b
Ethernet PHY Type                 : External Switch Using Reverse MII
Memory size in MB                 : 8
Country code                      : ALL

*** Press any key to stop auto run (1 seconds) ***
From: (Anonymous) Date: March 2nd, 2010 02:47 pm (UTC) (Link)

продолжение...

Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.27.34 (texas@fedora11) (gcc version 4.1.2) #7 Wed Oct 7 16:24:51 MSD 2009
Detected Broadcom 0x6348 CPU revision b0
CPU frequency is 256000000 Hz
8MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: 1.0.37-1.5
console [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: 96348R-A
Determined physical RAM map:
 memory: 00800000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00000800
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00000800
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 2032
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
PID hash table entries: 32 (order: 5, 128 bytes)
Dentry cache hash table entries: 1024 (order: 0, 4096 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 5588k/8192k available (1851k kernel code, 2604k reserved, 330k data, 128k init, 0k highmem)
Calibrating delay loop... 255.48 BogoMIPS (lpj=510976)
Mount-cache hash table entries: 512
net_namespace: 592 bytes
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bus: 00 index 0 io port: [8000000, 800ffff]
bus: 00 index 1 mmio: [30000000, 37ffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
detected lzma initramfs
initramfs: LZMA lc=1,lp=2,pb=2,origSize=512
audit: initializing netlink socket (disabled)
type=2000 audit(0.307:1): initialized
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  б╘ 2001-2006 Red Hat, Inc.
msgmni has been set to 16
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console handover: boot [early0] -> real [ttyS0]
bcm63xx_enet MII bus: probed
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
bcm963xx: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6, board type 96348R-A, and tagid bc300.
bcm963xx_flash: Partition 0 is CFE offset 10000802a5de8 and length c0062100800cc318
bcm963xx_flash: Partition 1 is kernel offset bff00802a5de8 and length c0062100800cc318
bcm963xx_flash: Partition 2 is rootfs offset 120000802a5de8 and length c0062100800cc318
bcm963xx_flash: Partition 3 is nvram offset 10000802a5de8 and length c0062100800cc318
bcm963xx_flash: Partition 4 is linux offset 1e0000802a5de8 and length c0062100800cc318
bcm963xx_flash: Spare partition is 1e0000 offset and length 10000
Creating 5 MTD partitions on "bcm963xx":
0x00000000-0x00010000 : "CFE"
0x00010100-0x000d0000 : "kernel"
mtd: partition "kernel" doesn't start on an erase block boundary -- force read-only
0x000d0000-0x001f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=1E0000, len=10000
0x001e0000-0x001f0000 : "rootfs_data"
0x001f0000-0x00200000 : "nvram"
0x00010000-0x001f0000 : "linux"
From: (Anonymous) Date: March 2nd, 2010 02:49 pm (UTC) (Link)

Re: продолжение...

bcm63xx_wdt started, timer margin: 30 sec
Registered led device: adsl-fail
Registered led device: ppp
Registered led device: ppp-fail
Registered led device: power
Registered led device: stop
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 128k freed
Please be patient, while OpenWrt loads ...
- preinit -
Press CTRL-C for failsafe
jffs2 not ready yet; using ramdisk
mini_fo: using base directory: /
mini_fo: using storage directory: /tmp/root
- init -

Please press Enter to activate this console. bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (1)]
roboswitch: Probing device eth0: Failed to enable switch
roboswitch: Probing device eth1: No such device
roboswitch: Probing device eth2: No such device
roboswitch: Probing device eth3: No such device
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
bcm63xx-spi bcm63xx-spi.0:  at 0xfffe0c00 (irq 9, FIFOs size 63) v0.1.2
jffs2: Too few erase blocks (1)



BusyBox v1.14.4 (2009-10-07 16:11:21 MSD) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 KAMIKAZE (bleeding edge, r17965) ------------------
  * 10 oz Vodka       Shake well with ice and strain
  * 10 oz Triple sec  mixture into 10 shot glasses.
  * 10 oz lime juice  Salute!
 ---------------------------------------------------
root@OpenWrt:/#
From: (Anonymous) Date: March 2nd, 2010 02:51 pm (UTC) (Link)

Re: продолжение...

root@OpenWrt:/# help

Built-in commands:
------------------
        . : [ [[ alias bg break cd chdir command continue echo eval exec
        exit export false fg getopts hash help jobs kill let local printf
        pwd read readonly return set shift source test times trap true
        type ulimit umask unalias unset wait


root@OpenWrt:/# busybox
BusyBox v1.14.4 (2009-10-07 16:11:21 MSD) multi-call binary
Copyright (C) 1998-2008 Erik Andersen, Rob Landley, Denys Vlasenko
and others. Licensed under GPLv2.
See source distribution for full notice.

Usage: busybox [function] [arguments]...
   or: function [arguments]...

        BusyBox is a multi-call binary that combines many common Unix
        utilities into a single executable.  Most people will create a
        link to busybox for each function they wish to use and BusyBox
        will act like whatever it was invoked as!

Currently defined functions:
        [, [[, arping, ash, awk, basename, brctl, bunzip2, bzcat,
        cat, chgrp, chmod, chown, chroot, clear, cp, crond, crontab,
        cut, date, dd, df, diff, dirname, dmesg, du, echo, egrep,
        env, expr, false, fgrep, find, free, grep, gunzip, gzip,
        halt, head, hexdump, hostid, httpd, hwclock, id, ifconfig,
        init, insmod, kill, killall, killall5, klogd, length, less,
        ln, lock, logger, logread, ls, lsmod, md5sum, mesg, mkdir,
        mkfifo, mknod, mktemp, mount, mv, nc, netmsg, netstat, nice,
        nslookup, passwd, pgrep, pidof, ping, ping6, pivot_root,
        pkill, poweroff, printf, ps, pwd, rdate, reboot, reset,
        rm, rmdir, rmmod, route, sed, seq, sh, sleep, sort, start-stop-daemon,
        strings, switch_root, sync, sysctl, syslogd, tail, tar,
        tee, telnet, telnetd, test, time, top, touch, tr, traceroute,
        true, udhcpc, umount, uname, uniq, uptime, vconfig, vi,
        watchdog, wc, wget, which, xargs, yes, zcat

root@OpenWrt:/# uname -a
Linux OpenWrt 2.6.27.34 #7 Wed Oct 7 16:24:51 MSD 2009 mips GNU/Linux

root@OpenWrt:/# free
              total         used         free       shared      buffers
  Mem:         5716         5196          520            0          236
 Swap:            0            0            0
Total:         5716         5196          520

root@OpenWrt:/# cat /proc/meminfo
MemTotal:         5716 kB
MemFree:           504 kB
Buffers:           236 kB
Cached:           1128 kB
SwapCached:          0 kB
Active:           1640 kB
Inactive:          616 kB
SwapTotal:           0 kB
SwapFree:            0 kB
Dirty:               0 kB
Writeback:           0 kB
AnonPages:         908 kB
Mapped:            552 kB
Slab:             1848 kB
SReclaimable:      288 kB
SUnreclaim:       1560 kB
PageTables:        168 kB
NFS_Unstable:        0 kB
Bounce:              0 kB
WritebackTmp:        0 kB
CommitLimit:      2856 kB
Committed_AS:     3020 kB
VmallocTotal:  1032148 kB
VmallocUsed:      1012 kB
VmallocChunk:  1031100 kB
From: (Anonymous) Date: March 2nd, 2010 02:53 pm (UTC) (Link)

Re: продолжение...

root@OpenWrt:/# cat /proc/cpuinfo
system type             : bcm63xx/96348R-A (0x6348/0x00B0)
processor               : 0
cpu model               : Broadcom BCM6348 V0.7
BogoMIPS                : 255.48
wait instruction        : yes
microsecond timers      : yes
tlb_entries             : 32
extra interrupt vector  : yes
hardware watchpoint     : no
ASEs implemented        :
shadow register sets    : 1
core                    : 0
VCED exceptions         : not available
VCEI exceptions         : not available

root@OpenWrt:/# ps
  PID USER       VSZ STAT COMMAND
    1 root      1448 S    init
    2 root         0 SW<  [kthreadd]
    3 root         0 SW<  [ksoftirqd/0]
    4 root         0 SW<  [events/0]
    5 root         0 SW<  [khelper]
   31 root         0 SW<  [kblockd/0]
   57 root         0 SW   [pdflush]
   58 root         0 SW   [pdflush]
   59 root         0 SW<  [kswapd0]
   60 root         0 SW<  [aio/0]
   76 root         0 SW<  [mtdblockd]
  216 root      1440 S    /bin/sh /etc/init.d/rcS S boot
  218 root      1444 S    /bin/ash --login
  220 root      1440 S    logger -s -p 6 -t sysinit
  228 root      1452 S    syslogd -C16
  230 root      1432 S    klogd
  242 root       868 S    /sbin/hotplug2 --override --persistent --set-worker /
  314 root      1444 S    udhcpc -t 0 -i eth0 -b -p /var/run/eth0.pid -R
  389 root         0 SW<  [bcm63xx-spi.0]
  534 root      1436 S    /usr/sbin/httpd -p 80 -h /www -r OpenWrt
  538 root      1436 S    telnetd -l /bin/login.sh
  560 nobody     856 S    /usr/sbin/dnsmasq -K -D -y -Z -b -E -s lan -S /lan/ -
  587 root      1432 S    watchdog -t 5 /dev/watchdog
  598 root      1124 S    /usr/sbin/dropbear -p 22 -P /var/run/dropbear.1.pid
  621 root      1440 R    ps
crazybert From: crazybert Date: February 21st, 2010 06:15 pm (UTC) (Link)
Привет!

ВО-первых огромное спасибо за статьи.

DSL-2640U B2. Собрал прошивку из исходников (3-06-04-3C00).

К сожалению есть одна проблема, как и на остальных прошивках:

Использую режим Port Map, Enable virtual ports.

Default - LAN4
Все остальные интерфейсы объединены в группу.

Идея в том, чтобы раздавать инет только на LAN4.
LAN3 подключен к локалке.

Проблема в том, что при включении режима Enable virtual ports WLAN-клиенты не получают ответ от DHCP, подключеному к LAN3. При этом на LAN2 и LAN1 ответы приходят.

Форум dlink молчит.

Понимаю что не много не по теме, но всё-же мало ли приходилось сталкиваться.

Спасибо!



gus4koff From: gus4koff Date: July 5th, 2011 02:09 pm (UTC) (Link)
А может эта прошивка открыть IP over Ethernet с привязкой к MAC-адресу?
16 comments or Leave a comment
profile
pudeev
User: pudeev
Name: pudeev
Website: My LJ
calendar
Back May 2009
12
3456789
10111213141516
17181920212223
24252627282930
31
page summary
tags